Tutorials DetailCraft help Walkthroughs
Steel stair generator
A steel stair from the floor-to-floor height, the run and the width: the rise and going by a rule set you choose, landings, rails and balusters, shop drawings and a cut list with weights.
Written for DetailCraft 0.10. The same help is inside the app: press F1.
The stair generator makes a whole steel stair from a few numbers: the stringers, the treads, landings when the flight is too high, handrails with posts and balusters, the fixing holes in the stringers, a cut list with weights, and the shop drawings. It starts from the Stair tool, like the plain stair (see Stairs), with one switch added.
Place a steel stair
- Choose Stair in the Place group, or press SS.
- On the right, tick Use the steel stair generator.
- Choose the rule set for where the stair is built, the rise (floor to floor; 0 = up to the next level), the run available (0 = let the rule decide), the clear width and the tread type: chequer plate, grating or folded plate pan.
- Set the stringer section, the landings (by the rule, or a number), the handrails (both sides, one, none), the rail height and the baluster gap.
- Click a grid intersection: that is the foot of the first riser.
Select the stair (click a stringer, tread or rail) to change any setting; the properties show the risers, going, pitch, flights and landings, the steel in it, the cut list and the rule set's sources.
The rule sets
The rule set limits the shape of the stair: the rise and going, 2 × riser + going, the pitch, the landing, the rail height and the largest opening. DetailCraft offers the ones below; the region is a setting, not a guess. Open Where this rule set's numbers come from in the properties: each number names its source and says how well it was checked.
- International Building Code 2021: riser 4 to 7 in., tread at least 11 in., rails 34 to 38 in. The 12 ft limit between landings is shown as not read and the rail numbers as read in handouts quoting the code: confirm them before relying on them.
- OSHA 29 CFR 1910.25 and 1910.29 (industrial standard stairs): 30° to 50°, riser at most 9.5 in., tread at least 9.5 in., at least 22 in. wide, landings as wide as the stair and 30 in. deep, a top rail used as the handrail 36 to 38 in. These were read in the regulation itself.
- Approved Document K 2013, England (general access and utility stairs): the rise and going ranges and 2 × riser + going 550 to 700 mm, read in the government-commissioned report that tabulates them. The document gives DetailCraft no rail height, so the height you set is used and the Problems list says so.
A rule set that is not here is not guessed: the stair then follows the plain 600 to 650 mm comfort rule and says it has no rule.
What it works out
- Risers and going. The fewest risers whose 2 × riser + going sits in the middle of the rule's range, without the going falling under the rule's minimum. With a run given, the going is the run over the treads and anything outside the rule is said.
- Flights and landings. A flight higher than the rule allows is split with a landing as wide as the stair and not less than the rule's minimum; you can also ask for landings. A landing is a frame of two side beams and two cross angles under a cover, on two posts.
- Treads. Chequer plate is a welded plate (6 mm by default, the pattern is not added to the weight). A folded plate pan has a return at the nosing and is bolted through the stringer web: two holes 2 mm larger than the bolt at 0.3 and 0.7 of the depth. Grating is drawn as the plate of equal weight (bearing bar depth × thickness ÷ pitch); the cross bars and banding are not counted and the cut list says so.
- Rails. A pipe top rail on posts along each flight and each landing, a baluster gap that no sphere larger than the rule's opening passes (100 mm at most by default).
Drawings, cut list, export
- The flight is one assembly; the rails are another (both sides are the same assembly, made twice). Each has its assembly drawing, and the stringer's drawing shows its holes.
- The stair sheet (ST-…) shows each flight's stringer straight with the hole stations written from the lower end, and the tread detail: section, nosing, return and the end flange with its holes.
- Cut list and weights in the properties lists every section and length with quantities and kilograms; Download the cut list (CSV) saves it.
- Everything goes to the bill of materials, NC files and IFC as ordinary parts (IfcMember, IfcColumn, IfcPlate).
Good to know
- This is a starting point, not a design. Nothing is checked for strength or deflection; the rule set only limits the shape.
- Stringer ends against the floors are cut square and not detailed; landing posts stand to the floor below and have no base plates.
- Placing the stair as one element in BimCraft is not wired yet.