Calculations

Calculations

• Cable length through each run

  For each cable, the runs it passes through and its length in each.

  length in a run = Σ segment length × 1000 over that run's segments on the path

  Conduit and tray fill, cable schedule addons/electrical/lib/mep/carrier.js

  • CadCraft
  • BimCraft
  64-bit

• Cable schedule length

  The length of each cable in the schedule, with slack and an allowance at each end.

  length m = (route mm × (1 + slack) + 2 × ends mm) ÷ 1000, rounded to 0.1

  Conduit and tray fill, cable schedule addons/electrical/lib/mep/carrier.js

  • CadCraft
  • BimCraft
  64-bit

• Cable list read from CSV

  Reads cable tags, outside diameters and counts from a CSV file.

  Conduit and tray fill, cable schedule addons/electrical/lib/mep/carrier.js

  • CadCraft
  • BimCraft
  64-bit

• A run moved, turned or scaled

  Applies a move, rotation, scale or mirror to a run's centerline and its scale.

  p′ = M · p; sc = √|det M|; k′ = k ÷ sc; z′ = z × sc

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Section width in drawing units

  The drawn width of a duct section.

  width = w ÷ k

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Branches found on mains

  Finds where a run's end sits on another run's centerline, the angle between them and how far the branch is cut back.

  sin = |t_main × t_branch|; cut = (W_main ÷ 2) ÷ sin; opening = W_branch ÷ sin; angle = round(asin(sin) × 180 ÷ π × 10) ÷ 10

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Elbows, transitions and straight pieces

  The fittings of a run and the start and end of each straight piece along its centerline.

  T = R tan(θ ÷ 2), R = r × W; mitred: T = (W ÷ 2) tan(θ ÷ 2); elbow length = R θ or 2T; transition L = max(max(ΔW ÷ 2, ΔH) ÷ tan 15° ÷ k, minimum)

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Length in feet or meters

  Converts a length in drawing units to feet or meters.

  feet = du × k ÷ 12; meters = du × k ÷ 1000

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Sheet-metal area of a length of duct

  The surface area of a length of duct in square feet or square meters.

  ft² = perimeter × du × k ÷ 144; m² = perimeter × du × k ÷ 1e6

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Elbow area and angle

  The sheet-metal area of an elbow and the angle in its name.

  area = perimeter × centerline length; name angle = round(θ × 180 ÷ π)

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Transition area

  The sheet-metal area of a transition between two sizes.

  rectangular: bottom + top + two sides as trapezoids over their slant lengths; other: (pₐ + p_b) ÷ 2 × slant length

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Straight pieces

  The length and area of each straight piece of a run.

  du = s₁ − s₀; length = lenOut(du); area = perimeter × du

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• Schedule totals

  The total duct length, total sheet-metal area and number of fittings.

  length = Σ rows; area = Σ duct areas + Σ fitting areas

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• A run in the other unit system

  Converts a run's sizes and airflows between inches with cfm and millimeters with L/s.

  size × 25.4 or ÷ 25.4; airflow × 0.47194745 or ÷ 0.47194745

  Duct runs, fittings and schedule addons/hvac/lib/duct.js

  • CadCraft
  64-bit

• A typed duct size

  Reads a size such as 24x12 or Ø14.

  Duct runs, fittings and schedule addons/hvac/main.js

  • CadCraft
  64-bit

• A point pulled onto a run's centerline

  Moves a point picked inside a duct's outline onto its centerline, to start or end a branch there.

  inside when distance ≤ W ÷ 2 + 1e-9

  Duct runs, fittings and schedule addons/hvac/main.js

  • CadCraft
  64-bit

• Schedule table in the drawing

  The rows of the duct schedule placed in the drawing.

  shown length and area = value.toFixed(1), trailing zeros removed

  Duct runs, fittings and schedule addons/hvac/main.js

  • CadCraft
  64-bit

• Schedule CSV

  Writes the duct schedule as CSV.

  length, perimeter, area: 3 decimals; velocity: 0 decimals (inch units) or 2; friction rate: 4 decimals

  Duct runs, fittings and schedule addons/hvac/main.js

  • CadCraft
  64-bit

• Liters per second in one cfm

  The factor that converts airflow from cubic feet per minute to liters per second.

  1 cfm = 0.3048³ ÷ 60 × 1000 L/s = 0.4719474432 L/s exactly

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  64-bit

• Millimeters per drawing unit

  The factors that take a run's coordinates, sizes and airflow to millimeters and L/s.

  draw = k × 25.4 (inch) or k; size = 25.4 or 1; lps = CFM_LPS or 1

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  64-bit

• Turn at a corner

  The angle a run turns through at a corner, in degrees.

  turn = acos(u·v ÷ (|u| |v|)) × 180 ÷ π

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  64-bit

• Runs handed to the engine

  Each run's vertices in millimeters, its section size in millimeters, and its free ends with their airflow.

  vertex mm = p × draw; w mm = w × size; z mm = z × draw

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  64-bit

• Fan point matched to a run end

  Finds the run end the fan sits on and takes its height.

  nearest end by √(Δx² + Δy²); accepted when ≤ 60 mm

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  64-bit

• Terminal airflows

  The airflow in L/s at each free end of the network.

  L/s = q × lps factor of the run

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  64-bit

• Pascals to inches of water

  Converts a pressure in pascals to inches of water gauge.

  in. w.g. = Pa ÷ 249.08891

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  Exact

• Network result CSV

  Writes the result rows as CSV.

  length 2 decimals; airflow 1; velocity 2; rate 3; pressures 1

  Duct network pressure: drawing adapter addons/hvac/lib/ductnet.js

  • CadCraft
  64-bit

• Numbers read from an IES file

  Splits the numeric part of an IES file into numbers.

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• IES candela values and luminaire size

  Scales the candela table and converts the luminous opening to millimeters.

  cd = value × multiplier × ballast factor; lumens = lamps × lumens per lamp; size mm = value × 304.8 (feet) or × 1000 (meters)

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Full set of horizontal planes

  Mirrors the horizontal planes of a symmetric IES file to cover 0 to 360 degrees.

  quadrant: a, 180 − a, 180 + a, 360 − a; bilateral: a, 360 − a

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• EULUMDAT lamp flux and watts

  Adds up the lamp flux and wattage of the lamp sets in an EULUMDAT file.

  lumens = Σ |count| × flux; watts = Σ watts

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• EULUMDAT candela scale

  Turns the file's cd per 1000 lm values into candela.

  cd = value × (lumens ÷ 1000) × (LORL ÷ 100) × conversion factor

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Position in an angle table

  Finds the two table angles on either side of an angle and the fraction between them.

  f = (x − a_lo) ÷ (a_hi − a_lo)

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Candela in a direction

  The luminous intensity at a vertical and horizontal angle, interpolated from the table.

  I = (1 − f_h) (I₀₀ (1 − f_v) + I₀₁ f_v) + f_h (I₁₀ (1 − f_v) + I₁₁ f_v)

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Luminaire axes

  The nadir, C0 and C90 directions of an aimed and rotated luminaire.

  n = aim ÷ |aim|; r₀ = axis − (axis·n) n, normalized; r = r₀ cos t + (n × r₀) sin t

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Illuminance at a point

  The direct illuminance in lux at a point on a surface from all luminaires.

  E = LLF × Σ I(γ, C) × scale × cos θ ÷ d², d in meters

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Calculation grid

  The points the illuminance is computed at: cell centers inside the area at the working height.

  nₓ = max(1, round(width ÷ spacing)); x = x₀ + (width ÷ nₓ) × (i + 0.5)

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Minimum, average, maximum and uniformity

  The statistics of the grid values.

  avg = Σ E ÷ n; uniformity = min ÷ avg; min ÷ max

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Area and lighting power density

  The area in square meters, the total lumens and watts, and the watts per square meter.

  area m² = |Σ (xᵢ yᵢ₊₁ − xᵢ₊₁ yᵢ)| ÷ 2e6; LPD = watts ÷ area

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Checks against typed targets

  Compares the average, minimum, uniformity and power density with the targets the person typed.

  avg ≥ target; min ≥ target; min ÷ avg ≥ target; LPD ≤ limit

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Grid CSV

  Writes each grid point and its illuminance.

  x, y, z = round(mm); lux = value.toFixed(1)

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Lighting report CSV

  Writes one row per area with its totals and statistics, then every grid point.

  area and lux 1 decimal; lumens and watts 0; W/m² and min ÷ avg 2

  Luminaire files and point-by-point illuminance addons/lighting/lib/mep/photometry.js

  • CadCraft
  • BimCraft
  64-bit

• Inputs of an illuminance run

  The mounting height, working height, grid spacing and light loss factor asked for a run.

  mount ≥ 100 mm; work ≥ 0; spacing ≥ 50 mm; 0.05 ≤ LLF ≤ 1

  Luminaire files and point-by-point illuminance addons/lighting/main.js

  • CadCraft
  • BimCraft
  64-bit

• Result printed in the command line

  The summary line of an illuminance run.

  min, avg, max: whole lux; uniformity 2 decimals; area and W/m² 1 decimal

  Luminaire files and point-by-point illuminance addons/lighting/main.js

  • CadCraft
  • BimCraft
  64-bit

• A click landing on a connection, end or line

  Finds the connection point, line end or point on a line within reach of a click.

  nearest within tol; a point on a line is ranked with distance + 0.1 × tol

  P&ID placement, zones and values written to the drawing addons/pid/main.js

  • CadCraft
  64-bit

• A line cut around an inline symbol

  Cuts a process line either side of a symbol placed on it, so the symbol's ends meet the line's.

  u = (b − a) ÷ |b − a|; cut points = at ± u × half

  P&ID placement, zones and values written to the drawing addons/pid/main.js

  • CadCraft
  64-bit

• A symbol's connection landed on a picked point

  Moves a new symbol so its nearest connection sits exactly on the connection or line end that was clicked.

  offset = R(rot) · connection × size; at = picked − offset

  P&ID placement, zones and values written to the drawing addons/pid/main.js

  • CadCraft
  64-bit

• Scale of an imported DEXPI drawing

  The drawing units per millimeter used to place an imported P&ID.

  k = 1 ÷ (millimeters per drawing unit)

  P&ID placement, zones and values written to the drawing addons/pid/main.js

  • CadCraft
  64-bit

• Imported stream table values

  Converts stream temperature, pressure and flows to display units and writes them into a table in the drawing.

  °C = K − 273.15 (1 decimal); bar = Pa ÷ 1e5 (3); kg/h = kg/s × 3600 (1); kmol/h = mol/s × 3.6 (3); fractions 3 and 4 decimals

  P&ID placement, zones and values written to the drawing addons/pid/main.js

  • CadCraft
  64-bit

• Drawing coordinates for the area calculator

  Hands the symbols' positions and the meters per drawing unit to the hazardous-area calculator.

  toMetres = (millimeters per drawing unit) ÷ 1000

  P&ID placement, zones and values written to the drawing addons/pid/main.js

  • CadCraft
  64-bit

• Consequence zones drawn to scale

  Draws each zone of the consequence calculator as a circle or polygon at the picked point.

  k = 1000 ÷ (millimeters per drawing unit); center = at + (cx, cy) × k; radius = r × k

  P&ID placement, zones and values written to the drawing addons/pid/main.js

  • CadCraft
  64-bit