Tutorials CivilCraft help Getting started
What's new in 0.9 (earlier)
Corridor and terrain templates, snaps and Pick buttons while drafting, GIS analysis with an attribute table, shade, solar yield, comfort and wind studies for a site, a 3D Render view, and the Point clouds and WaterCraft add-ons.
Written for CivilCraft 0.10. The same help is inside the app: press F1.
This is what changed in CivilCraft 0.9, compared with 0.8.1. CivilCraft 0.9 is part of CadCraft Studio 0.9 and its eight apps. The big parts are corridor and terrain templates, snaps while you draw, GIS analysis, studies of a site's sun, solar yield, comfort and wind, and two add-ons: Point clouds and WaterCraft.
New
Corridor and terrain templates
- Corridor templates. Open Surface › More › Corridor templates… (or type
TEMPLATES). A template is a small cross-section with components, offsets, slopes, materials and point codes. Keep them in the project, in My library or as a.cctemplates.jsonfile. The template editor shows a true-scale drawing and lists problems as you type. - Build from templates by station. Select an alignment and turn on Build from templates by station in its Properties. Each side of each region has its own pavement list and its own end condition. Add a corridor under Corridors on this alignment puts several corridors on one alignment.
- Terrain templates. Surface › More › Terrain templates… (or type
TERRAINTEMPLATES) drapes layered materials such as topsoil or pavement and base on a terrain, with area and volume per layer. See Corridor templates and terrain templates.
Drafting
- Snaps. The Alignment, Pad, Parcel, Mass, Feature line, Measure, Boundary and Catchment tools snap to survey points, PIs, corners, vertices and structures, with a label by the marker. Hold ⌥Alt for a free point.
- Pick buttons, tangent and move, copy, rotate. Pad, parcel and feature-line corners have typed Easting and Northing boxes and a crosshair Pick button. Properties also has Tangent from two points for alignments and Move, copy and rotate for alignments, pads, parcels and feature lines. See Draft with snaps, picked corners and move, copy, rotate.
- Render view in 3D. The Render button on the 3D bar draws the land with natural colours, sky, haze and soft shadows. It does not change the model. The Sun menu now has Apply and Close buttons. See View the site in 3D.
- Panels open one section at a time. The left panel and the Properties panel open one section and close the others, and the Landscape ribbon tiles that hold several tools are split buttons.
GIS analysis
- Analyze. Surface › More › Analyze offers buffer, overlay, spatial join, select by attribute or shape, and measure. Each tool makes a new layer in one undo step.
- Attribute table. A layer's three-dots menu has Attribute table… and Style by attribute…. See Analyze GIS layers and Work with a layer's attribute table.
The site: sun, solar, comfort and wind
- Environment section. Select a mass: the Environment section sits under Sun hours in its Properties. It has a shade study (map, table, animation, CSV), solar yield from a typical-year weather file (.epw) and outdoor comfort (UTCI).
- Wind, screening only. Run wind study colours the ground from sitting to uncomfortable for each wind direction in the weather file. It is unvalidated and the panel says so.
- Pedestrian wind (OpenFOAM) add-on. Off until you switch it on in Settings › Add-ons. OpenFOAM is software you install yourself. See Shade, solar yield and outdoor comfort.
Point clouds (add-on)
- Switch on Point clouds in Settings › Add-ons; a Point clouds tab appears in the right-hand panel. Open a LAS or LAZ file, clean it, sort it into ground, vegetation and buildings, build the ground, contours and volumes, and export LAS or LAZ. See Point clouds from a drone or scanner.
WaterCraft (add-on)
- Switch on WaterCraft (water distribution) in Settings › Add-ons; a WaterCraft tab appears. It has demands from customers, fire flow at every hydrant, which main outage matters most, and water age and chlorine, each saved as CSV. See WaterCraft: demands, fire flow, outages and water age.
Working together
- In a Live session you see each other's cursors and names in the plan. Library plants: CivilCraft Landscape starts from its default Library collection, CivilCraft landscape.
In every app
- Hints show as Bootstrap tooltips, and the start tip can be closed.
- A panel's tab strip that does not fit scrolls instead of being cut off.
- Browser tab titles read
<document> - CivilCraft | CadCraft. - Settings has a Layout section where the layouts are a drop-down of two-line choices.
- Weight and temperature units are in Settings › Global › Units.
- The language list shows the languages the build has files for. Languages other than English are machine drafts.
Fixed
- The address lookup and EnergyPlus check add-ons could not be switched on; now they can.
- The help now says the Point clouds add-on writes a cleaned cloud as LAS 1.4 or LAZ.
- Clicking the selected object's own grip no longer starts a grip drag that stopped a waiting Pick.
Honest limits
- The example corridor templates are placeholders from no standard; an engineer must check them. Terrain templates add no surface and are not drawn in 3D or in the section view. The second corridor on an alignment is not in the IFC export. There is no taper between two templates by station.
- Point clouds were tested on made-up files, not a real drone survey. Only LAS and LAZ are read.
- GIS analysis was tested on made-up layers.
- Shade, solar and comfort are planning estimates; wind is unvalidated screening. None of it is a design value.
- WaterCraft is a calculation aid checked on made-up networks. A water engineer decides what the numbers are worth.
- Languages beyond English are machine drafts.
- Windows installers are not code-signed, and the macOS disk image is not notarized.
Earlier: 0.8 and 0.8.1
This is what changed in CivilCraft 0.8 (2026-11-01) and 0.8.1 (2026-11-02), compared with 0.7. The big new parts are tools that test your grading and your site (rain, earthwork, routes, ponds, progress) and six calculation windows for ground, roads, survey, mines, links and rail.
New
Test your grading
- Make it rain. Make it rain… (under Surface) drops a storm on the graded ground. You watch the water run off the pads, pond in the low corners and overtop the ponds that are too small. The run is animated and gives the volumes, the peak outflow and a CSV of every pond. The default cell is coarse so a first look is quick; a finer cell is slower. Ponds that overtop also show up in the Problems panel.
- Earthwork balancer. Earthwork balancer… raises or lowers a pad until cut equals fill, and shows the haul table between them.
- Best route. Best route…: pick a start and an end, and CivilCraft finds the cheapest path across the terrain that keeps to your grade and curve limits, then makes an alignment from it.
- Detention ponds. Detention ponds… works out stage and storage from your ground, takes outlet devices (orifice, weir, V-notch, spillway), routes a storm through the pond and checks the peak held back, the drawdown time and the freeboard.
- Progress from surveys. Progress from surveys… compares drone or scan surfaces from different dates with the ground as it was and with the design: percent complete by volume, over-dug and over-filled areas, stockpiles, and when the work finishes at this pace (marked as an estimate).
Know the site
- Address to site. Address to site… lines up open parcel, building, zoning, soil, flood and terrain data on one site. You can keep the site in the project file: the typed address, each source with the day you fetched it and its licence, and what came back. Reopen or share the project and the site is still there, with nothing fetched again. You can also save it as a site file or send it to BimCraft. See Address to site.
Ground, roads, survey, mines, links and rail
- Soils and slopes. Soils and slopes… draws the soil profile between borings you type. Bishop's method then searches the critical circle on your ground, with a water table, a surcharge and an earthquake coefficient; settlement of a footing gets consolidation, immediate settlement and time.
- Junctions and striping. Junctions and striping… puts legs together with curb returns (one radius per leg, or three-centre returns), the sight distance for the design speed, a check of the sight triangles, crosswalks, stop bars, markings and signs with a sign schedule. They are drawn on the plan and saved as a .dxf with named layers.
- Survey adjustment. Survey adjustment… runs a least-squares adjustment of a traverse or network: adjusted coordinates, error ellipses, the chi-squared test and a flag on the measurement that does not fit. Free networks, closing a traverse by the compass rule and RW5, GSI, JobXML or CSV field files are included, and the adjusted points save as CSV.
- Open pits. Open pits… turns drill samples into a block model and the ultimate pit within your slope angle, with the strip ratio, a table by bench and a grade and tonnage curve. Nested pits by revenue factor and a production schedule with a discounted cash flow are there too.
- Radio links. Radio links… checks line of sight over your ground with the earth's bulge, the first Fresnel zone, link budget, fade margin and multipath outage, and gives the mast height that would clear the path. It also does fibre loss budgets, route quantities and the wind on a tower.
- Rail turnouts. Rail turnouts… makes a turnout from its frog number, crossovers between parallel tracks and a structure gauge tilted by cant and widened on a curve. A turnout can sit at a station of an alignment.
See Soils, junctions, survey adjustment, pits, radio links and turnouts.
In every app
- Languages. 54 languages, ten of them new. Languages other than English are machine drafts until a native speaker reads them. Help topics are still mostly English.
- Toolbar rows. Settings › General › Toolbar rows: Wrap (as before), 2 rows or 1 row. CivilCraft's Ribbon shows the most used tool large, the next ones small, and the rest behind the group name's arrow.
- Input devices. Trackpad, pen, 3D mouse, controller and MIDI can drive the apps.
- Problems. A Problems panel that warns in every app, with checks that read regulation packs.
- Live. A view of who is where in a Live session.
- Add-ons. An add-on listing, with lighting add-ons.
- Connect your AI. Any assistant you connect can drive CivilCraft's tools. It ships with a note that one-click connecting inside CadCraft Studio and the hosted connector are not ready yet. See Let an AI assistant work with your site.
Fixed in 0.8.1
- DWG classes section. It was read as the wrong type (GitHub cadcraft#5). Fixed in CivilCraft along with CadCraft, BimCraft, ModelCraft and TakeoffCraft.
- Switching language while running. CadCraft Studio and the packed editions can change language at run time. They were English only before. Not yet tested on every platform: tell us if the language does not change.
Not in this version yet
- These are calculation aids. Every result in the new windows needs an engineer's check. Soil strengths start from typical values for the soil group, and the window says so.
- Make it rain. A run on the sample site can take over two minutes in the browser at a fine cell. It was checked against hand cases and a V-shaped catchment, not yet on a real graded site.
- Address to site. It reads open data files you bring, and was tested on our own files only. Trees are not a source. Fetching sources for you waits on the privacy wording.
- Progress from surveys. Tested on made-up surveys only. Progress on sheets and markups (MarkupCraft) and scan against model (BimCraft) are not built.
- Soils and slopes. Circular surfaces only: no wedge or block search and no tension crack.
- Junctions. One radius per leg, no truck swept paths, and they do not yet go into the corridor.
- Field files. The readers were written from public format descriptions and tried on files we made. Real instrument files are wanted.
- Links and rail. Radio links: free-space loss and multipath only (no rain fade or antenna patterns), and no railway standard: every rail limit is a placeholder, with draft numbers no railway engineer has checked.
- Windows and macOS. 0.8 is not code-signed. Windows may warn, and macOS asks for right-click then Open.
Everything else is in Not built yet. For the earlier release, see What's new in 0.7.