Tutorials DetailCraft help Getting started
What's new in 0.9 (earlier)
UK Blue Book steel sizes and unequal angles, shop drawings for every part in one PDF set, My profiles for custom sections, P-Delta and natural frequencies, ASCE 7 wind loads, seismic site and combinations, and live cursors with Follow.
Written for DetailCraft 0.10. The same help is inside the app: press F1.
This is what changed in DetailCraft 0.9, compared with 0.8.1. 0.9 brings the UK steel sizes, a shop drawing for every part in one go, a larger Analysis tab for frames, and a view of each other's cursors when you work together.
New
UK steel and shop drawings
- UK steel sizes. The profile lists now carry 976 sizes from the Steel for Life Blue Book: UB, UC, PFC, EA, UEA, CHS, SHS and RHS, with the cold-formed hollow sections kept apart (their names start with CF). Names are written family first, such as UB305x165x40 or SHS100x100x5.0, and typing it the way drawings say it works too: 305x165x40 UB, L100x100x10, SHS100x5. See Profile catalog.
- Unequal angles. UEA angles keep both legs through IFC in and out and through NC files, and a mirror turns the piece end for end.
- Every shop drawing at once. Choose Shop drawing in the Output group with nothing selected. The window lists every part mark, previews any of them, and Download all saves one PDF with a page per mark, each titled "Sheet 3 of 42". Download this sheet saves the one you are looking at. Channels, angles and hollow sections now get sheets too. See Make shop drawings.
- My profiles. A custom profile can now be kept for every new model. In the Custom profile form, leave Keep in My profiles ticked; the My profiles list under it has Keep, Use here and Remove. The list is kept in this browser (up to 200), not in your account. See Plates and profiles.
Analysis
- Second order (P-Delta). Tick Second order (P-Delta) beside Run in the Analysis tab and the axial forces act on the deflected frame. Plates and rigid floors stay first order, with a warning. See Forces, reactions and deflections.
- Natural frequencies. The Finite elements: natural frequencies block under the results finds the lowest modes of the same model, with period and effective modal mass, and shows a mode on the model. See Forces, reactions and deflections.
- Wind loads and seismic site. Three new blocks in the Analysis tab: Wind loads (ASCE 7 directional procedure), Seismic site and system (ASCE 7) and ASCE 7 load combinations. See Wind, seismic site and ASCE 7 combinations.
Working together
- Cursors and names. In a Live session each person's pointer is drawn in the model with their name and colour, and what they selected gets a box.
- Follow a person. Open People in the session and choose Follow on a name; your view moves with theirs. The host can choose Ask everyone to follow me. See Follow a person in a Live session.
In every app
- Tooltips are Bootstrap tooltips, the start tip card has a close button, tab strips scroll sideways when they do not fit, and the browser tab names the open document followed by DetailCraft and CadCraft.
Fixed
- A custom profile was lost when you started a new model.
- Channels, angles and hollow sections were missing from the shop-drawing set.
Honest limits
- The wind, seismic and finite element blocks are checking aids. Your engineer reviews the results; they are not a code check. The USGS lookup was tested on a stand-in, not on the live service.
- Finite elements and P-Delta were checked against hand and closed-form answers, not a real building. Buckling analysis is not built.
- No UK fabricator has tried the UK sizes yet, and NC files for unequal angles have not run on a machine.
- The shop-drawing set is PDF only.
- Languages beyond English are machine drafts.
- The Windows installers are not code-signed (More info, then Run anyway); the macOS disk image is not notarized (right-click, then Open).
Earlier changes are in the 0.8 and 0.8.1 notes further down this page.
Earlier: 0.8 and 0.8.1
This is what changed in DetailCraft 0.8 (1 November 2026) and 0.8.1 (2 November 2026), compared with 0.7. 0.7 checked steel members; 0.8 plans the lifts, proposes the connections, checks the foundations and the rebar, and frames timber and light-gauge walls, floors and roofs.
New
Erection
- Erection plan and movie. In the Erection tab, describe a crane (where it stands, its highest hook, the rigging that is not in the chart) and type the rows of its load chart. DetailCraft lifts the model one assembly at a time, in phase order and tier by tier, and checks each lift against the chart at its radius and against the margin you set. Save movie writes one HTML file that plays offline in any browser, on a phone too. Lifts that are over the chart, past it or too high are in Problems. It is a plan from your numbers, not a lift plan. See Erection plan and movie.
Connections
- Connection autopilot. The Autopilot tab looks at every joint that has no connection and proposes one from the shapes: base plates, shear tabs, end plates for the beams you mark as moment beams, splices and gussets. Give a uniform load or one end shear and the bolt count follows the bolt's design strength. Add them all adds the proposals as one undo step. They are starting values to review, not a connection design.
- Constructability checks. Problems for a bolt a wrench cannot reach, bolts too close for the socket, fillet welds outside their size limits and hollow sections that hold water. Weld access is new: an all-round fillet weld that a welder's torch cannot reach is listed with the part in the way and the share of the weld affected. See Constructability checks.
Foundations and rebar
- Foundation checks. The Foundation tab checks footings, combined footings and mats on the soil you describe: bearing, sliding and overturning from service loads; flexure, shear, punching, development and minimum steel from factored loads (ACI 318-19). A column near an edge or a corner is checked with the section cut off by the footing's edge. Settlement comes from the soil's modulus, a flexible mat is solved on springs from a subgrade modulus, and pile groups and retaining walls have panels of their own. Column loads can be typed or taken from the Analysis. See Foundation checks.
- Rebar congestion map. The Congestion tab draws a heat map of each footing as seen from above: where the bars leave too little room for concrete to get down, against the clear-spacing rule and, if you give them, the largest aggregate and the vibrator head. See Rebar congestion map.
Framing and supply
- Timber and light-gauge framing. The Framing tab frames wall, floor and roof panels with every piece, a cut list, the stock to buy and a shop drawing to scale. Place as members puts the pieces in the model, and PDF sheets saves one sheet for each panel. The sizes, spacing and headers are yours: DetailCraft does not check that they carry the load. See Timber and light-gauge framing panels.
- Supplier stock and lead times. The Supply tab reads a supplier's stock list (CSV) and shows, for each section the cut list buys, whether there is enough in stock and how long the wait is. Shorts and late sections are in Problems. Nothing is ordered. See Supplier stock and lead times.
Analysis and design
- What breaks first? In the Analysis tab, the button finds the strength combination that governs, the weakest member, how far the loads can grow before the first member reaches its limit, and the weakest end plate or shear tab where its bolts' shear strength is known. It needs the combinations and a design code first. Bearing, block shear, welds and prying are not checked. Your connected assistant can ask the same.
- Live. Tick Live: solve again after each edit and the frame is solved again after each edit.
- Concrete, more. A slender column in a non-sway frame is designed for its magnified moment (ACI 318-19 6.6.4.5). The seismic period can be taken from the analysis by Rayleigh's method. A slab made of plates gets the steel each layer needs from its moments, and the one-way shear. See Check concrete members and make seismic loads.
- For an engineer to check. The foundation, concrete and What breaks first results are aids. Wind loads are not built.
In every app
- Languages. The help is in 54 languages. Those beyond English are machine drafts until a native speaker reads them; ten are new (Lithuanian, Latvian, Bosnian, Marathi, Telugu, Albanian, Afrikaans, Filipino, Swahili, Uzbek).
- Toolbar rows. Settings › General › Toolbar rows chooses wrap, 2 rows or 1 row. A bar that already fits stays as it is; the rest scroll sideways.
- Property grid. The footing's fields use the shared grid: collapsible categories and a compact density. Typed arithmetic such as 2*450 still works.
- Input devices. Trackpad, pen, 3D mouse, controller and MIDI can drive the apps. See Navigate in 3D.
- Problems panel. The warnings of the new checks above appear in the same Problems panel as before.
- Connect your AI. Your own assistant, connected through CadCraft Studio, works with all eight apps and sees only what you allow. One-click connect, the hosted connector and your own API key in Studio are still to come. See Use DetailCraft with an AI assistant.
Fixed in 0.8.1
- Languages in Studio. Studio and the packed editions can switch language at run time; before, they were English only. It is not yet tested on every platform: tell us if the language does not change.
- Crossing-window select. The 0.8.1 installers carry the select-by-window behavior already right in the 0.8 web build; an older installer did not.
- Tablets in portrait. Spare grid height goes to the canvas, and the sheet layout starts at 760 px or less.
Not in this version yet
- Send NC to a machine is not released.
- Wind loads for concrete are not built, and the concrete and foundation checks are for an engineer to review.
- Code signing. The Windows installers and the macOS .dmg are not signed, so Windows may warn and macOS asks for a right-click, then Open.
Earlier changes are in What's new in 0.7.